1997- 2002 255 LPH C5 in-tank Fuel Pump Module Assembly

RFPK-055-255 – 1997-2003 C5 Corvette High Performance Fuel Pump Kit, T6, RXP255JE

This pump will NOT work on 2003 and newer fuel systems.
This would be the VIN after 114930 (last six digits) built November 25, 2002. 

The FPA-055-255 fuel pump module features:

• Racetronix RXP255JE E-85 compatible Turbine Jet-Pump
• Racetronix T6 Anodized aluminum reservoir (bucket) with check-valve assembly
• 30-micron filter sock
• Filter screen
• Dual-circuit upgraded PTFE in-tank harness
• High-pressure non-kinking fuel tube
• Oetiker clamps
• Silicon pump seal
•  FPWKH-052  Plung and Play hotwire harness.
• Fully Assembled & Tested

Why a Racetronix Fuel Assembly? Racetronix direct-fit T6 Aluminum Module with HP Turbine Jet Pump:

In 2021,TI Automotive (Walbro) GM’s OE supplier, discontinued manufacturing the C5 Corvette fuel system components. Racetronix set out to design a new module that would maintain the factory functionality but at the same time provide enhanced performance and reliability. Racetronix new module is over 50% larger which provides more fuel capacity. This enhanced capacity reduces the chance of fuel starvation under heavy fuel demands, high g-forces and low-tank levels. The all aluminum construction helps dissipate heat which reduces the chance of hot fuel (aeration) with high-flow pumps and climate conditions.

The Racetronix FPA-055-255 module is fitted with our RXP255JE turbine pump which is a direct-fit replacement for the factory Walbro jet-pump therefore the full functionality of the fill bucket is maintained. The aluminum module (bucket) allows the fuel pump to use its jet + venturi function to keep the pump immersed in fuel at all times regardless of the tank fuel level. This aids in preventing fuel starvation under hard cornering and acceleration. Keeping the pump immersed in fuel also helps prevent moisture damage which can shorten the pump’s life. The RXP255JE pump has slightly higher flow than comparable Walbro pumps allowing it to maintain similar flow at higher LSx pressure of 58 PSI vs. 43.5 PSI for other pumps. There are no Walbro pumps which are spec’d at 255LPH @ 58PSI @ 13.5V. This has been a constant source of confusion on car forums due to misinformation being posted. This pump assembly in combination with our FPWK-052 wiring upgrade kit will support approximately 550-600 rear-wheel horsepower (RWHP) using the factory regulator and fuel lines. This HP number may be less with forced induction applications which require richer air/fuel mixtures and higher fuel pressure. Please see tech note below! Please factor in a 20-25% safety margin between what your motor needs and what your fuel system can supply.

* Our FPWK-052 is required for a HP pump to meet stated performance specifications because the factory wiring was not designed to handle high-performance pumps which draw more than twice the power of a factory pump. A performance reduction of 15-25% in pump performance can be expected along with reduced reliability when a HP pump is run off of the factory harness.

GM type no-kink solvent resistant fuel tube:

This fuel tube is the same type used by GM from the factory. The fuel tube is kink-resistant thanks to its ribbed design. Its special composition makes it more resistant to the solvents in today’s pump gas (i.e. toluene, Xylene, MTBE, Ethanol) as compared to rubber / neoprene which dries out, swells and cracks.

Upgraded dual-circuit PTFE in-tank harness (ITWH-052):

The Racetronix ITWH-052 in-tank harness has upgrades the factory PTFE wiring from a single 16 gauge to two 14 gauge multi-strand copper wires. This helps reduce voltage drop and at the same time maintains the same level of resistance to fuel solvents as the factory wiring. Generic Walbro kits do not use Teflon wire but rather a much less expensive plastic type.

Direct-power pump wiring (no adapters/splices):

The Racetronix in-tank wiring harness is a one-piece assembly. One end has the Walbro connector and the other is fitted with GM type terminals which are installed directly into the factory connector making it true plug & play. Generic wiring harnesses require cutting and splicing of the factory wiring.

Redundant in-tank ground loop (solves factory problem):

The factory in-tank wiring has the ground from the pump and ground from the power connector split into two circuits which relies on push-lock terminals and the module’s body as a ground junction source. We have seen these connectors loose and in some cases corroded. If one were to fail the pump would lose power. Racetronix has redesigned the grounding system with a daisy-chain / loop through circuit. This way there are three grounds all tied together thereby making circuit failure next to impossible. An extra ground is also provided via the FPWH-052 external upgrade harness via a ground lug. This further enhances the fuel module’s grounding system and eliminates the chance of a floating ground condition. A floating ground condition will cause a static buildup and potential fuel
ignition. All harnesses are assembled using our computerized crimp-quality monitoring system and then circuit-checked for the utmost in reliability.

Fuel Screen / Silicon gasket seal:

A new filter sock, screen, and silicon pump seal are installed.